亚洲一区欧美在线,日韩欧美视频免费观看,色戒的三场床戏分别是在几段,欧美日韩国产在线人成

噴嘴空化模型建立與有效性試驗驗證
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家自然科學基金項目(51306069)


Establishment and Experimental Validation of Nozzle Cavitation Model
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 圖/表
  • |
  • 訪問統計
  • |
  • 參考文獻
  • |
  • 相似文獻
  • |
  • 引證文獻
  • |
  • 資源附件
  • |
  • 文章評論
    摘要:

    提出了一種針對噴嘴孔內空化現象的數值計算模型——噴嘴空化模型,并進行了可視化試驗以驗證其模型有效性,其中噴嘴空化模型考慮了液相與氣相之間相變、氣泡動力學、湍流擾動及不凝性氣體影響等諸多因素,并采用噴孔內空化數對相變速率方程進行了修正。將基于噴嘴空化模型的數值計算結果與試驗結果及基于Schnerr—Sauer模型的計算結果進行對比分析,結果顯示:在2種空化模均采用默認參數的前提下,噴嘴空化模型與Schnerr—Sauer模型計算所得噴孔內空化現象變化趨勢均與試驗結果吻合良好,即噴嘴孔內空化現象隨噴射壓力提高而加強,且在發展空化至超空化流態過渡過程中空化特征長度漲幅遠高于其他流態過渡情況;噴嘴空化模型計算所得空化特征長度在各流態下均與試驗結果吻合良好,Schnerr—Sauer模型計算空化特征長度則低于試驗結果,兩者與試驗值的最大誤差均發生在超空化階段,其中噴嘴空化模型計算值為試驗值的92%,Schnerr—Sauer模型計算值為試驗值的65%。該結果表明,所建立噴嘴空化模型可用于較為準確地模擬噴嘴孔內空化現象的變化趨勢及空化特征長度。

    Abstract:

    Fuel spray atomization strongly affects engine economic performance and emissions, which in turn is significantly influenced by nozzle cavitation phenomenon with high injection pressure in diesel and GDI engine. A new cavitation model named “nozzle cavitation model” was presented to specifically simulate nozzle cavitation while the corresponding visual experiment was made to validate this model. The presented model considered phase change, bubble dynamics, turbulent pressure fluctuations and noncondensable gases while the equation of phase-change rate was amended by cavitation number. The comparison of simulation results with “nozzle cavitation model”, simulation results with Schnerr—Sauer cavitation model and visual experimental results showed that the development trend of nozzle cavitation from “nozzle cavitation model” and Schnerr—Sauer cavitation model both agreed well with experimental results, that was, the normalized cavitation length was increased with the enhancement of injection pressure and the maximal increase appeared on the transition from development cavitation to super cavitation. The normalized cavitation length from “nozzle cavitation model” agreed well with experimental results while that from Schnerr—Sauer cavitation model was obviously less than that of experimental results. The maximum errors of normalized cavitation length simulated with the two cavitation models both appeared at super cavitation stage, which were 8% with “nozzle cavitation model” and 35% with Schnerr—Sauer cavitation model. The conclusion that the predictive capability of “nozzle cavitation model” was superior to that of Schnerr—Sauer cavitation model for simulation of nozzle cavitation was mainly because of the turbulent viscosity in near-wall region calculated from the former was lower than that from the latter, the threshold pressure value to produce phase change from the former was higher than that from the latter, the bubble number density from the former was amended by volume fraction of noncondensable gases and the equation of phase-change rate from the former was amended by cavitation number.

    參考文獻
    相似文獻
    引證文獻
引用本文

麻斌,高瑩,劉宇,劉洪岐,鄧海鵬,王亞娣.噴嘴空化模型建立與有效性試驗驗證[J].農業機械學報,2017,48(5):377-384. MA Bin, GAO Ying, LIU Yu, LIU Hongqi, DENG Haipeng, WANG Yadi. Establishment and Experimental Validation of Nozzle Cavitation Model[J]. Transactions of the Chinese Society for Agricultural Machinery,2017,48(5):377-384.

復制
分享
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2017-02-09
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期: 2017-05-10
  • 出版日期: