亚洲一区欧美在线,日韩欧美视频免费观看,色戒的三场床戏分别是在几段,欧美日韩国产在线人成

基于動態識別區和B樣條曲線的智能叉車避障路徑規劃
CSTR:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家重點研發計劃項目(2018YFD0701002)、國家自然科學基金項目(51108194)、廣東省基礎研究及應用研究重大項目(2016KZDXM028)和廣東省科技計劃項目(2017B020206005)


Obstacle Avoidance Path Planning for Intelligent Forklift Truck Based on Dynamic Identification Zone and B-spline Curve
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 圖/表
  • |
  • 訪問統計
  • |
  • 參考文獻
  • |
  • 相似文獻
  • |
  • 引證文獻
  • |
  • 資源附件
  • |
  • 文章評論
    摘要:

    為降低干果倉儲智能叉車自主避障誤警率,提高倉儲空間有效利用率,結合叉車運行環境特點,基于激光傳感器,設立探測范圍隨車速、等效轉向角變化的動態識別區,有效探測叉車行進方向上的障礙物;將獲得的障礙物特征控制點作為分割點,采用四次五階準均勻B樣條曲線,分前后段合并生成滿足叉車最小轉彎半徑、曲率連續、最大轉向輪角速度等多約束條件下的避障路徑;對倉庫中的直行路段和轉彎路段進行避障路徑規劃試驗,結果表明所得避障路徑滿足各項約束,曲率不大于1.06×10-3mm-1,等效轉向角不大于60°,等效轉向輪角速度不大于1.05rad/s,驗證了算法的可行性。

    Abstract:

    In order to reduce the false alarm rate of autonomous obstacle avoidance for intelligent forklift trucks in dried fruit warehouse and improve the utilization rate of warehouse space, combining with the characteristics of the operating environment of forklift truck, and basing on the laser sensor SICK-LMS111 and SICK-NAV350, a dynamic identification zone that the detection range was changed along with the speed and equivalent steering angle was set up to effectively detect obstacles in the direction of travel. Then, feature control point obtained by obstacles was taken as the segmentation point, and the quartic fiveorder quasiuniform Bspline curves were used to generate the obstacle avoidance path by combining front and rear segments of curve, which met the multiconstraint conditions such as the minimum turning radius, the continuous curvature and the maximum angular velocity of steering wheel. By carrying out the obstacle avoidance path planning tests on the straight road section and the turning in the warehouse, the results showed that the obstacle avoidance paths satisfied various constraints, the curvature was not more than 1.06×10-3mm-1, equivalent steering angle was not more than 60°, angular velocity of equivalent steering wheel was not greater than 1.05rad/s, which effectively verified the feasibility of the algorithm. It can be used as a reference for obstacle avoidance technology of similar large warehouse intelligent vehicles.

    參考文獻
    相似文獻
    引證文獻
引用本文

呂恩利,阮清松,劉妍華,王飛仁,林偉加,董冰.基于動態識別區和B樣條曲線的智能叉車避障路徑規劃[J].農業機械學報,2019,50(1):359-366. LU Enli, RUAN Qingsong, LIU Yanhua, WANG Feiren, LIN Weijia, DONG Bing. Obstacle Avoidance Path Planning for Intelligent Forklift Truck Based on Dynamic Identification Zone and B-spline Curve[J]. Transactions of the Chinese Society for Agricultural Machinery,2019,50(1):359-366.

復制
分享
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2018-10-15
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期: 2019-01-10
  • 出版日期:
文章二維碼